| Type | Standard | Model for
Sensor Communications
Unit *1 |
|
|
| NPN output | E3X-HD11 | E3X-HD6 | E3X-HD14 | E3X-HD0 |
| PNP output | E3X-HD41 | E3X-HD8 | E3X-HD44 |
|
| Connecting method | Pre-wired | Wire-saving
Connector
*2 | M8
connector | Communications
Unit connector |
| Light source (wavelength) | Red, 4-element LED (625 nm) |
|
|
|
| Power supply voltage | 12 to 24 VDC ±10%, ripple (P-P) 10% max. | Supplied from the connector
through the Sensor
Communications Unit |
|
|
| Normal mode | 720 mW max.
(Current consumption: 30 mA max. at 24 VDC, 60 mA max. at 12 VDC) |
|
|
|
| Eco ON | 530 mW max.
(Current consumption: 22 mA max. at 24 VDC, 44 mA max. at 12 VDC) |
|
|
|
| Eco LO | 640 mW max. (Current consumption: 26 mA max. at
24 VDC, 53 mA max.at 12 VDC) | – |
|
|
| Control output | Load power supply voltage: 26.4 VDC max., open-
collector output
Load current:
Groups of 1 to 3 Amplifier Units: 100mA max.,
Groups of 4 to 16 Amplifier Units: 20mA max.
Residual voltage:
At load current of less than 10 mA: 1 V max.,
At load current of 10 to 100 mA: 2 V max.
OFF current: 0.1 mA max. | – |
|
|
| Protection circuits | Power supply reverse polarity protection, output
short-circuit protection and output reverse
polarity protection | Power supply reverse polarity
protection and output short-
circuit protection |
|
|
Super-high-speed
mode (SHS) *3 | NPN outputs: Operate or reset: 50 μs
PNP outputs: Operate or reset: 55 μs | – |
|
|
High-speed Mode
(HS) | Operate or reset: 250 μs (default setting) |
|
|
|
Standard Mode
(STND) | Operate or reset: 1 ms |
|
|
|
Giga-power Mode
(GIGA) | Operate or reset: 16 ms |
|
|
|
| Maximum connectable Units | 16 units | with E3X-CRT: 16 units
with E3X-ECT: 30 units |
|
|
Mutual interference
prevention | Possible for up to 10 units (optical communications sync) *3 |
|
|
|
| Auto power control (APC) | Always ON |
|
|
|
| Other functions | Power tuning, differential detection, DPC, timer (OFF-delay, ON-delay, or one-shot),
zero reset, resetting settings, and Eco mode |
|
|
|
Ambient illumination
(Receiver side) | Incandescent lamp: 20,000 lx max., Sunlight: 30,000 lx max. |
|
|
|
| Ambient temperature range | OOperating:
Groups of 1 to 2 Amplifiers: -25 to 55°C,
Groups of 3 to 10 Amplifiers: -25 to 50°C,
Groups of 11 to 16 Amplifiers: -25 to 45°C
Storage: -30 to 70°C
(with no icing or condensation) | Operating:
Groups of 1 to 2 Amplifiers:
0 to 55°C,
Groups of 3 to 10 Amplifiers:
0 to 50°C,
Groups of 11 to 16 Amplifiers:
0 to 45°C,
Groups of 17 to 30 Amplifiers:
0 to 40°C
Storage: -30 to 70°C
(with no icing or condensation) |
|
|
| Ambient humidity range | Operating and storage: 35% to 85% (with no condensation) |
|
|
|
| Insulation resistance | 20 MΩ min. (at 500 VDC) |
|
|
|
| Dielectric strength | 1,000 VAC at 50/60 Hz for 1 minute |
|
|
|
Vibration resistance
(destruction) | 10 to 55 Hz with a 1.5-mm double amplitude for
2 hours each in X, Y, and Z directions | 10 to 150 Hz with a 0.7-mm
double amplitude for 80 minutes
each in X, Y, and Z directions |
|
|
Shock resistance
(destruction) | 500 m/s2 for 3 times each in X, Y, and Z
directions | 150 m/s2 for 3 times each in
X, Y, and Z directions |
|
|
| Degree of protection | IEC 60529 IP50
(with Protective Cover attached) | – |
|
|
Weight
(packed state/unit only) | Approx. 105 g/
Approx. 65 g | Approx. 60 g/
Approx. 20 g | Approx. 70 g/
Approx. 25 g | Approx. 65 g/Approx. 25 g |
| Case | Polycarbonate (PC) | Heat-resistant ABS
(connector: PBT) |
|
|
| Cover | Polycarbonate (PC) |
|
|
|
| Cable | PVC | – |
|
|
| Accessories | Instruction Manual |
|
|
|
