Article number | 6ES7522-1BH10-0AA0 | 6ES7522-1BL10-0AA0 |
| S7-1500, DQ 16x24VDC/0.5A BA | S7-1500, DQ 32x24VDC/0.5A BA |
General information |
|
|
Product type designation | DQ 16x24VDC/0.5A BA | DQ 32x24VDC/0.5A BA |
HW functional status | FS01 | FS01 |
Firmware version | V1.0.0 | V1.0.0 |
● FW update possible | Yes | Yes |
Product function |
|
|
● I&M data | Yes; I&M0 to I&M3 | Yes; I&M0 to I&M3 |
● Isochronous mode | No | No |
● Prioritized startup | Yes | Yes |
Engineering with |
|
|
● STEP 7 TIA Portal configurable/integrated from version | V13 / V13 | V13 / V13 |
● STEP 7 configurable/integrated from version | V5.5 SP3 / – | V5.5 SP3 / – |
● PROFIBUS from GSD version/GSD revision | V1.0 / V5.1 | V1.0 / V5.1 |
● PROFINET from GSD version/GSD revision | V2.3 / – | V2.3 / – |
Operating mode |
|
|
● DQ | Yes | Yes |
● DQ with energy-saving function | No | No |
● PWM | No | No |
● Oversampling | No | No |
● MSO | Yes | Yes |
Supply voltage |
|
|
Rated value (DC) | 24 V | 24 V |
permissible range, lower limit (DC) | 20.4 V | 20.4 V |
permissible range, upper limit (DC) | 28.8 V | 28.8 V |
Reverse polarity protection | Yes; through internal protection with 7 A per group | Yes; through internal protection with 7 A per group |
Input current |
|
|
Current consumption, max. | 30 mA | 60 mA |
Output voltage |
|
|
Rated value (DC) | 24 V | 24 V |
Power |
|
|
Power available from the backplane bus | 1.15 W | 1.15 W |
Power loss |
|
|
Power loss, typ. | 2.2 W | 3.8 W |
Digital outputs |
|
|
Type of digital output | Transistor | Transistor |
Number of digital outputs | 16 | 32 |
Current-sourcing | Yes | Yes |
Digital outputs, parameterizable | No | No |
Short-circuit protection | Yes | Yes |
● Response threshold, typ. | 1 A | 1 A |
Limitation of inductive shutdown voltage to | L+ (-53 V) | L+ (-53 V) |
Controlling a digital input | Yes | Yes |
Switching capacity of the outputs |
|
|
● with resistive load, max. | 0.5 A | 0.5 A |
● on lamp load, max. | 5 W | 5 W |
Load resistance range |
|
|
● lower limit | 48 Ω | 48 Ω |
● upper limit | 12 kΩ | 12 kΩ |
Output voltage |
|
|
● for signal “1”, min. | L+ (-0.8 V) | L+ (-0.8 V) |
Output current |
|
|
● for signal “1” rated value | 0.5 A | 0.5 A |
● for signal “1” permissible range, max. | 0.5 A | 0.5 A |
● for signal “0” residual current, max. | 0.5 mA | 0.5 mA |
Output delay with resistive load |
|
|
● “0” to “1”, max. | 100 µs | 100 µs |
● “1” to “0”, max. | 500 µs | 500 µs |
Parallel switching of two outputs |
|
|
● for logic links | Yes | Yes |
● for uprating | No | No |
● for redundant control of a load | Yes | Yes |
Switching frequency |
|
|
● with resistive load, max. | 100 Hz | 100 Hz |
● with inductive load, max. | 0.5 Hz; According to IEC 60947-5-1, DC-13 | 0.5 Hz; According to IEC 60947-5-1, DC-13 |
● on lamp load, max. | 10 Hz | 10 Hz |
Total current of the outputs |
|
|
● Current per channel, max. | 0.5 A; see additional description in the manual | 0.5 A; see additional description in the manual |
● Current per group, max. | 4 A; see additional description in the manual | 4 A; see additional description in the manual |
● Current per module, max. | 8 A; see additional description in the manual | 16 A; see additional description in the manual |
Cable length |
|
|
● shielded, max. | 1 000 m | 1 000 m |
● unshielded, max. | 600 m | 600 m |
Interrupts/diagnostics/status information |
|
|
Diagnostics function | No | No |
Substitute values connectable | No | No |
Alarms |
|
|
● Diagnostic alarm | No | No |
● Maintenance interrupt | No | No |
Diagnoses |
|
|
● Monitoring the supply voltage | No | No |
● Wire-break | No | No |
● Short-circuit | No | No |
● Group error | No | No |
Diagnostics indication LED |
|
|
● RUN LED | Yes; green LED | Yes; green LED |
● ERROR LED | Yes; red LED | Yes; red LED |
● Monitoring of the supply voltage (PWR-LED) | Yes; green LED | Yes; green LED |
● Channel status display | Yes; green LED | Yes; green LED |
● for channel diagnostics | No | No |
● for module diagnostics | No | No |
Potential separation |
|
|
Potential separation channels |
|
|
● between the channels | No | No |
● between the channels, in groups of | 8 | 8 |
● between the channels and backplane bus | Yes | Yes |
Isolation |
|
|
Isolation tested with | 707 V DC (type test) | 707 V DC (type test) |
Standards, approvals, certificates |
|
|
Suitable for safety functions | No | No |
Altitude during operation relating to sea level |
|
|
● Installation altitude above sea level, max. | 5 000 m; Restrictions for installation altitudes > 2 000 m, see manual | 5 000 m; Restrictions for installation altitudes > 2 000 m, see manual |
Dimensions |
|
|
Width | 25 mm | 25 mm |
Height | 147 mm | 147 mm |
Depth | 129 mm | 129 mm |
Weights |
|
|
Weight, approx. | 230 g | 280 g |
